Glovezilla
At Beeswift, we spend time developing and structuring amazing products, including our
new Glovezilla range.
Each glove comes with a retail ready header card. This strong robust card also adopts the same colour size chart
as the outer box and is 100% recyclable.
Each card also comes with its own barcode making it easy for the retailer
to add to their existing system. By adding a colour size chart it is easy to determine which size of Glovezilla glove
you are purchasing.
Easy to read titles on the front of the card, along with technical details for each glove, make
choosing the right product for the job simple.
Translation of the titles and technical information on the rear of
the card make this product perfect for the European markets.
As a company, we are continuing our efforts to ethically source products and reduce waste, whilst producing
products that are fit for purpose and ready to retail. Our outer boxes are all recyclable and we have reduced
our ink coverage.
• 13 Gauge Liner.
• 20% UHMW PE+ 80% rubber
• 100% TPE Fully Injection coating.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.
• EN 388:2016+A1:2018
• Level 3 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 2 - Puncture Resistance
• Level C - TDM Cut Resistance (ISO 13997)
• Level P - Impact Protection
• 13 Gauge Liner.
• 20% UHMW PE+ 80% rubber
• 100% TPE Fully Injection coating.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.
• EN 388:2016+A1:2018
• Level 3 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 2 - Puncture Resistance
• Level D - TDM Cut Resistance (ISO 13997)
• Level P - Impact Protection
• Premium soft grain Leather.
• Natural Coloured backing.
• Half elastication to back of cuff.
• Para-Aramid lining.
• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 4 - Puncture Resistance
• Level D - TDM Cut Resistance (ISO 13997)
• HPPE 47.4%, Polyester 20.1%, Glass Fibre 17.2%, Steel 14%, Spandex 1.3%.
• Food Safe and washable.
• Extremely high cut protection.
• Suitable for general food preparation and areas where high cut protection is needed.
• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 2 - Puncture Resistance
• Level F - TDM Cut Resistance (ISO 13997)
• 100% Para-Aramid Liner.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.
• EN 388:2016+A1:2018
• Level 1 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 2 - Tear Resistance
• Level 3 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)
• EN ISO 11612: 2015
• A1 - Limited Flame Spread (Method A)
• F2 - Contact Heat (250C for between 10 to 15 Seconds)
• 100% Para-Aramid Liner.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.
• EN 388:2016+A1:2018
• Level 1 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 2 - Tear Resistance
• Level 3 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)
• EN ISO 11612: 2015
• A1 - Limited Flame Spread (Method A)
• F2 - Contact Heat (250C for between 10 to 15 Seconds)
• 100% Para-Aramid Liner.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.
• EN 388:2016+A1:2018
• Level 1 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 2 - Tear Resistance
• Level 3 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)
• EN ISO 11612: 2015
• A1 - Limited Flame Spread (Method A)
• F2 - Contact Heat (250C for between 10 to 15 Seconds)
• 100% Para-Aramid Liner.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.
• EN 388:2016+A1:2018
• Level 1 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 2 - Tear Resistance
• Level 3 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)
• EN ISO 11612: 2015
• A1 - Limited Flame Spread (Method A)
• F2 - Contact Heat (250C for between 10 to 15 Seconds)
• HPPE 40.9%, Nylon 14.1%, Polyester 15.9%, Glass Fibre 21.3%, Spandex 7.8% Liner.
• 100% Nitrile rubber coating.
• Ventilated back.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications
• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 2 - Puncture Resistance
• Level C - TDM Cut Resistance (ISO 13997)
• 18 Gauge knit
• Grey PU palm coating
• UHMWPE liner
• Comfortable ergonomic fit
• EN388: 2016
• Level 4 - Abrasion
• Level X - Cut Resistance
• Level 4 - Tear Resistance
• Level 2 - Puncture
• Level E - ISO 13997 Cut Resistance
• Foodsafe (Except for fatty foods)
• 18 Gauge knit
• Grey nitrile palm coating
• HPPE liner
• Comfortable ergonomic fit
• EN388: 2016
• Level 4 - Abrasion
• Level X - Cut Resistance
• Level 4 - Tear Resistance
• Level 2 - Puncture
• Level F - ISO 13997 Cut Resistance
• Foodsafe (Except for fatty foods)
• 100% Para-Aramid Liner.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.
• EN 388:2016+A1:2018
• Level 1 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 2 - Tear Resistance
• Level 3 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)
• EN ISO 11612: 2015
• A1 - Limited Flame Spread (Method A)
• F2 - Contact Heat (250C for between 10 to 15 Seconds)
• 100% Para-Aramid Liner.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.
• EN 388:2016+A1:2018
• Level 1 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 2 - Tear Resistance
• Level 3 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)
• EN ISO 11612: 2015
• A1 - Limited Flame Spread (Method A)
• F2 - Contact Heat (250C for between 10 to 15 Seconds)
• Premium Cowhide Split Leather
• G-150gram Thinsulate and Micro Fleece
• Nylon Cuff
• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 3 - Tear Resistance
• Level 4 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)
• EN 511:2006
• Level 1 - Convective Cold Resistance
• Level 3 - Contact Cold Resistance
• Level X - Water Penetration
• Premium goatskin Leather with reinforced stitching
• Reinforced Para-aramid Lining
• TPR back of hand protection
• ARC Flash resistant ASTM F2675/F2675M 55cal/cm2
• ARC Flash Heat attenuation factor 97.1%
• EN 388:2016+A1:2018
• Level 3 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 3 - Puncture Resistance
• Level E - TDM Cut Resistance (ISO 13997)
• Level P - Impact Resistance
• EN 407:2004
• Level X - Burning Behaviour
• Level 1 - Contact Heat
• Level X - Convective heat
• Level X - Radiant heat
• Level X - Small splashes of Molten Metal
• Level X - Large splashes of Molten Metal
• 40% polyester +60% Latex
• High performance anti-vibration gloves
• EN388: 2016
• Level 4 - Abrasion
• Level X - Cut Resistance
• Level 4 - Tear Resistance
• Level 2 - Puncture
• Level B - ISO 13997 Cut Resistance
EN10819:
Medium Frequency Spectrum "M" - 0.865 Pass
High Frequency Spectrum "H" - 0.598 Pass
• Microfiber knitting
• Single nitrile coating
• 18 gauge nylon
• Breathable
• Mixed spandex
• Oil and wet resistance
• High level abrasion resistance
• EN 388: 2016
• Level 3 - Abrasion
• Level X - Cut Resistance
• Level 2 - Tear Resistance
• Level 1 - Puncture
• Level A - ISO 13997 Cut Resistance
• Para-Aramid 25.5, Steel 11%, Polyester 16.6%, Polycotton 46% Liner.
• Latex palm Coating.
• Ventilated back.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.
• EN 388:2016+A1:2018
• Level 3 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 2 - Puncture Resistance
• Level D - TDM Cut Resistance (ISO 13997)
• 15-gauge nylon liner
• Fully coated with latex
• Water resistant
• Dry/wet grip
• EN388: 2016
• Level 2 - Abrasion
• Level X - Cut Resistance
• Level 4 - Tear Resistance
• Level 1 - Puncture
• Level A - ISO 13997 Cut Resistance
• Double coated latex
• 13-gauge napped acrylic liner
• Wet/dry grip
• Extra cold resistance
• EN388: 2016
• Level 1 - Abrasion
• Level X - Cut Resistance
• Level 4 - Tear Resistance
• Level 1 - Puncture
• Level B - ISO 13997 Cut Resistance
• EN 511: 2006
• Level 0 - Convective Cold
• Level 1 - Contact Cold
• Level 1 - Water Permeability
• EN 407: 2004
• Level X - Burning Behaviour
• Level 2 - Contact Heat
• Level X - Convective heat
• Level X - Radiant heat
• Level X - Small splashes of Molten Metal
• Level X - Large splashes of Molten Metal
• HPPE 49%, Polyester 25%, Glass Fibre 12%, Steel 8%, Spandex 6% Liner.
• 100% Nitrile Rubber Coating
• 100% PVC TPR Back of hand protection.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.
• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 2 - Puncture Resistance
• Level D - TDM Cut Resistance (ISO 13997)
• 13 Gauge, HPPE, Polyester, Glass Fibre Green Liner.
• 100% Sandy Nitrile Coating
• 100% TPR Back of hand protection.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.
• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 3 - Puncture Resistance
• Level C - TDM Cut Resistance (ISO 13997)
• Level P - Impact Protection
• 13 Gauge, HPPE, Polyester, Glass Fibre Orange Liner.
• 100% Sandy Nitrile Coating
• 100% TPR Back of hand protection.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.
• EN 388:2016+A1:2018
• Level 4 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 3 - Puncture Resistance
• Level C - TDM Cut Resistance (ISO 13997)
• Level P - Impact Protection
• 13 Gauge, HPPE, Polyester, Glass Fibre Green Liner.
• 100% Foam Nitrile Coating
• 100% TPR Back of hand protection.
• Lightweight for maximum dexterity and comfort with sensitivity.
• Suitable for general assembly handling and engineering applications.
• EN 388:2016+A1:2018
• Level 3 - Abrasion Resistance
• Level X - Cut resistance (Coupe Test)
• Level 4 - Tear Resistance
• Level 3 - Puncture Resistance
• Level B - TDM Cut Resistance (ISO 13997)
• Level P - Impact Protection
